All About Information and Tips Car

Be careful when the car was vibrating force on while driving at high speeds. The owners old cars should be more careful and sensitive to the condition of the car. Because old cars usually have a complex problem of damage. One problem that often occurs is the strong vibration in all parts of the vehicle when the vehicle is moving, especially if high speed. If left unchecked it is very dangerous.

If your car shakes whenever you brake with a high speed, or just simply whenever you drive with a high speed generally, it usually means that that the car alignment is off. Although car services start to check the complete car alignment for you personally, the method is made much faster and cheaper in case you actually know about the specific component that‘s causing the matter.

Here are the actions of what you should do and cause it could happen :

1. Problem of Brake

The brakes are problematic can also cause vibrations of the car at high speeds, usually when the brake disc is not feasible ( uneven / forming wave ) when the brakes on the car will vibrate. Note also when you replace the brake linings, brake pads do not use a low quality because most of the material and its dimensions are not precise so that it can damage the disk disc.

2. Problem of Wheels

Tires are uneven in this case air pressure, or the quality is not the same tires can cause the car to vibrate at high speeds, try to always check the air pressure in each tire if there is one less wind immediately added. Experience tire is often less wind can cause more severe shockbreaker work, often also spread the steering system ( power steering ) due to an unbalanced tire.

3. Problem of Axle

Axle or wheel holder serves as a pedestal wheels and the successor to rev the engine to the wheels, axle at the front and rear wheels slightly different role which the front wheel axle also serves successor turns of the steering wheel so that if the front wheel axle problems, the vibration will be felt. This axle is rarely a problem but it never hurts to check axle automotive enthusiasts had checked the car if the previous three issues ( engine, brakes and tires ) .

T18.57

Diagnostic And Solve Steering Wheel Shakes When Brakes Are Applied

Break

When we're driving, vibration and noise from the cars we drive indeed can be a clue that something is wrong with the car. An example is to feel the strangeness of the steering wheel or steering wheel. Typically, Setur This steering can be an indicator of when the car has a problem, especially in the legs and also the braking system.

Diagnostic And Solve Steering Wheel Shakes When Brakes Are Applied

Many car owners who complain why the steering wheel was shaking when braking. Especially when the car is braking while in high speed. Vibration felt in the steering wheel is also getting stronger. In fact, according to them, the car in good shape and the legs just past the spooring and balancing process.

The problem is, the vibrations that appear on the steering wheel when the car drove at high speed because there are mostly on the legs. But if the vibrations on the steering wheel felt when applying the brakes or braking, usually caused more problems in the braking system does not work well. Especially in the automobile discs are in bad condition.

Vibration in the steering wheel when braking could be because the disc is not flat, edges begin to erode, the discs begin wavy or crooked, or even installation that is not straight and balanced. The disc is designed with a material that is strong, heat resistant and impact-resistant. But this does not mean that the disc can not be defective or damaged. Scouring dust or sand continuously, to a severe and use brake that turns thinning could also damage the disc surface of the disc.

If the problem is due to a disc that has begun to erode, broken or wavy, then replace it with a new more advisable. However, there are also circumventing this problem by turning the component and returns to its original shape. This method is less expensive, but less recommended because the quality of components produced certainly can not be justified .

And the other factor why Steering wheel shakes when brakes are applied, from age factor. The longer life of the brake discs, the possibilities bumpy ( broken ) also becomes larger.

and probably from quality issues brake ( disc pad ). Brake -based hardware tends to damage the disc. This often happens when a disc pad used in the braking system of your car turned out to be imitation.

T00.10

Diagnostic And How to Fix Car Pulls to One Side When Braking

Break

A car that pulls to at least one side could be annoying and likewise dangerous. This braking problem can caused by several different things, even the tires (see below ), but the most typical cause is really a frozen caliper. As time passes, a caliper can freeze up gradually, a process which will go unnoticed for an extended time period.

One way a caliper can freeze up is from the piston upon the caliper being stuck in its bore. When the dust boot that protects the piston coming from the elements gets torn, water and debris will penetrate the metal inside the caliper and cause rust and corrosion. When the piston is stuck, and also the fluid pressure can't push it back straight into the bore easily, the pressure upon the pads will certainly be uneven and also the car will pull. To repair this issue you‘ll need to restore the caliper.

Diagnostic And How to Fix Car Pulls to One Side When Braking

Another possibility could be that the pistons got bent, during a brake job or perhaps a car accident, and can't move freely anymore, causing the caliper to bind and limiting the quantity of pressure towards the pads.

The caliper also can freeze up when the caliper slide pins have lost lubrication simply since they Haven‘t been maintained properly. When the slide pins are your issue, they should be cleaned and lubricated or replaced. You can purchase an overhaul kit for calipers, but you are hard to locate and also your caliper might not be worth bringing to life. Buying a brand new caliper may cost more but you‘ll make up the value using the time you save. Been there, done that!

And also if the car stops straight on the brakes, but pulls to one side when you release the brakes, the brake hose needs to be replaced. the rubber gets old and somtimes can form a "one way valve" flap.. so the fluid is pushed into the caliper just fine, but it doesnt release on one side as quickly as the other.

when replacing the rubber lines, replace all 3 at the same time. the left front, right front and rear axle lines if one is worn, the others probly are too.

The Other Causes of a Pull to One Side When Braking

Another thing. Brake Fluid is hydroscopic (absorbs moisture) so keep the bottle and master cylinder closed as much as possible to prevent corrosion in the lines. As a parts guy I constantly saw people who had just done a brake job within the last 6 months who suddenly had line corrosion or seized calipers. The master cylinder being open for periods of time would actually absorb the humidity in the air and lead to this. It's worse in hot & humid Florida than other areas but something to be aware of.

T21.01

How to Fix Troubleshooting a Low Break Pedal in Your Car

Break

Your brakes are one of the most important section of your car. Without an intake system, you will just sit there. But a minimum of you won't hit a tree while you are just sitting there ! Seriously, brakes are not something to play around with. In case your car has a braking problem, whether it is weak brakes, a mushy pedal, grinding sounds - whatever your brake problem is, you have to troubleshoot and repair it when possible.

There will be only two plausible reasons for a coffee pedal: air inside the system; and excessive movement between linings and rotors or drums (because of insufficient adjustment, an out-of-round drum, or perhaps a wobbly disc that is knocking the pistons back to ensure that there is extra space to bring up before braking action begins). Here are some steps to fix this common brake problem.

1. Check Brake Fluid

There are a lot of instances once your brake pedal will feel low, but probably the most common is simply due to low brake fluid. This could be caused using a leak inside the brake line, or it could be since the fluid has broke down enough where It‘s low inside the master cylinder. Check the cylinder and add around you have to bring it to the right levels. You may even got to bleed the lines to ensure there isn‘t any air in them.

2. Change Fluid

Another common problem could be that the brake fluid could possibly be dirty, or contaminated with dust and grime. Look into the master cylinder and find out if it‘s a light color, or perhaps a dark color. If it‘s a dark, thick color you‘ll need to alter the fluid. To do that you have to remove the tires and obtain admittance to the bleeding screw upon the brakes. Open them up and let the fluid drain from the lines. Open in the master cylinder cover to push the fluid out quicker. Depress the brake pedal a couple of times to assist using this process. When the lines are dry you are able to close the screws and add new brake fluid. This‘ll probably take a minimum of 2 cans. Bleeding the brakes is likewise necessary when you add the new fluid to ensure that there‘s no air inside the lines.

3. Change Brake Pads

Once the brake pedal begins to travel too far it could be since the brake pads are worn right all the way down to the metal face. In case you notice the brake fluid remains where it ought to be, then remove the tires and check out the brake pads. when they‘re worn you will start to begin to see the rivet heads upon the brakes. This really is an indication the pads should be replaced.

4. Faulty Brake Power Boost

Some vehicles, that perform some towing, are designed with a brake power boost. These mechanisms kick in to assist the brakes when it comes with an excess load on them. Once they commence to fail It‘ll feel as if you need to press the brake quite a distance in an effort to stop. Check the ability boost mechanism to ensure It‘s working properly. Otherwise, then restore the power boost, or remove it and recalibrate the brake system to labor without it.

T05.16

Here Some Step and Tips to Change Wheels in Your Car

Wheel

For people who are new to driving your own car, of course there are still many things to be learned for the convenience of travel. One is about how to replace the tires themselves. This is particularly important if a sudden flat tire or a leak while on the trip. To that end, here are some steps on how to remove the tires and how to install it correctly.

the incidence of punctures or rupture may have ever experienced. Sure is hard to imagine if we did not have any knowledge of how to change a car tire. This article will guide you replace the tires from preparation until you are ready to resume the journey.

Changing tires that leak or rupture is one of the fundamental things that should be known by the driver of the car. If you 've never been before replacing tires, you should examine it soon as this information would have been useful someday.

The first thing to do when a tire suddenly deflated or leaking is you slowly pull over to a safe side street, quite roomy and has a hard surface to make the process of replacement tires. Do not suddenly pulled over, note the presence of other vehicles as well. After that, do not forget to activate the handbrake, turn on the hazard lights and warning triangle tides several meters behind the car. If you 're on a hill or a derivative, then use wood or stone to prop up car tires.

Next, prepare the necessary equipment such as wheel locks, car jack and spare tire course. Put all of this equipment in an accessible part that you do not need pacing.

Then open the manhole cover bolts if any. You could fit this part with a screwdriver. And loosen the bolt car by using wheel locks. To loosen, turn the bolt opposite clockwise. When loosen, done by bersebrangan between the screw that one with the next. Loosened just enough in advance, not to loose .

Set the car jack at the near the wheel to be replaced and has a solid structure. Typically, a guide to put the jack point is contained in the manual. But if not, then select the section near the wheel and has a basin or a place to put the jack point. Generally, every car has a jack point is. Make sure the jack is already perpendicularly between the ground and the car, then use the jack to lift the car tires to the position that you think is easy to remove the tire. If it starts to lift jack tilted, then lower and repeat with the jack position fix first.

After the the tire was lifted , then open the tire bolts until completely detached all. Save these screws because the round shape tends to be serious repercussions rolled on a highway and lost. Then remove the tire from its place and put it in a safe place in a sleeping position. Never put a tire in a standing position.

Take a spare tire or spare tire that has been prepared, and then install the proper position. You may need a little rattled when entering the tire into place really is right and fitting. Once completely fit, replace the bolts with bersebrangan way between the one with the next. Do not be tightened, just plug in position only until it feels heavy or hard enough.

Lower the jack slowly until the tire touches the ground intact. Remove the jack out of place. Then begin to tighten the bolts one by one with a cross pattern again and make sure the bolts are actually attached with strong and toned.
If it is already take the jack, wheel locks, tire your car and other equipment and then put back into the car. Congratulations, you 've been able to continue the journey back. Do not forget to repair a punctured tire had to be reusable

T18.22

How To Replace Radiator Coolant Flush in Your Car

Radiator

Your car's radiator and cooling system must be clean to become cool. As time goes on, your car's radiator builds solid deposits which will clog the cooling system. A fast, inexpensive radiator flush can keep the internal system in shape. It is crucial to alter antifreeze seasonally. Before you begin your radiator flush, ensure you have everything you‘ll need. There is nothing worse than draining your radiator only to realize you‘ll want to drive towards the auto store for something !

The most common mistakes made by users when the car is draining, filling or adding water to the radiator. Usually things are throwing angina serng passed through the valve by opening angina bolt near the cylinder head. Because of the error, then finally closed radiator is not perfect and can lead to overheating of the engine. This time the doctor car will share a little knowledge about how to replace a car radiator water, and how the ideal temperature. Here are some steps you should do to replace the water radiator of your car :

First all you have to open the radiator drain bolt located at the bottom of the radiator. Wait until the water radiator completely wasted.

Screw the cap back on and open the radiator exhaust duct exhaust bolts wind. After that, fill the radiator water until the water out through the exhaust wind duct bolt that had been opened.

Close the bolt exhaust air and let the radiator cap open. Start machine to get into the ideal temperature in an air-conditioning temperature die of course. The ideal temperature when the thermometer needle pointed to a half and the radiator fan starts spinning.

Review at the volume of water in the radiator. If the volume is reduced, then you can add water to the radiator in accordance with the maximum limits.

The next thing you need to do is look at the condition of the reserve tank. If the condition is quite dirty, drain the water radiator and radiator water is replenished with a new course to the maximum extent. Tighten the cap back on the radiator or reservoir.

When you first use the car after reduction, check again the volume of water in the radiator reserve tank. If reduced, there is something wrong in your radiator system.

The ideal temperature when the engine is turned on is 85-90 degrees Celsius. If it exceeds the normal temperature then you will experience overheating engine and an indication of a problem in your radiator.

T04.01

How To Cleaning Body of Car And Checking For Rust

Exterior

Start using the roof and liberally apply the shampoo solution till the dirt floats away. Following the roof, shampoo the bonnet and boot lid, sides, front and rear, including chromework and plastic fittings. If you‘re employing a wax or silicone shampoo, avoid getting it upon the windscreen like the wipers will smear when next used.

How To Cleaning Body of Car And Checking For Rust

Make use of a stiff brush to clear trapped dirt from behind plastic bumpers, mouldings, number plates and crevices around front and rear lamp clusters. Wipe anodised aluminium, with a coloured or gleaming silver finish, along with other brightwork having a damp cloth.

Open the doors and sponge the within metalwork and apertures. Finish using the wheels. If they‘ve complex surfaces, use a little, stiff brush to obtain straight into the crevices.

1. Remove Dust

First, of course, used to clean the dust that sticks to your car. Because if you wash your car immediately, can be fatal. For example, just when you wash the car and there is still dust off, will paint your car will be scratched. Causing scratchy smooth, and worse, scratches that appear

2. Remove The Inside

If you also wash the inside of the car as well, how good you are to remove all existing interior on the inside of the car to avoid damage. In addition, try to wash the inside of the car before you wash the outside of the car.

3. First With Water

Before washing with soap, flush the first car with clean water. You can take advantage of having high pressure hose

4. Use Shampoo For Car

Sometimes this is often forgotten by the owner of the car. They use any soap or shampoo to wash their cars. Causing baretan on their cars. We recommend that you use a special shampoo to clean the car. In addition to keeping the car's paint is more durable, it also gives the impression the car looks shiny.

5. Use a sponge or cloth Fine

I think, using special materials like sponge or jersey material is also very influential when you clean the car. Because with this material, will minimize the occurrence of scratches with sand or dust that might still be in the car.

6. Dry the Right Car

When drying the car, a few people leave them in a hot place. Actually this is not wrong, but it could result in car paint can be moldy. Therefore, we recommend that you put the car in the shade as soon as you are finished washing.

7. Using Polish

To further beautify paint your car, you can use more polish polish for your cat. Because with polish , your car will look like new, even though your car is outdated.